How to Make Firebricks (fire logs) and Wood Stove Logs for Free! (2024)

Today we’re proud to present another DIY project from a fellow Doing the Stuff Networker. Jamie Burke is a master atrepurposingtrash and junk. His latest project shared on our DTSN Facebook Groupnot only saves money, but would be very useful both now (free is always good) and after a SHTF event.

If you’d like to see more of howhe and our other members are Doing the Stuff, join us on our journey to self-reliance and preparedness!

Here’s Jamie’s down and dirty tutorial…

Firebricksand Wood Stove Logs Tutorial

This process only requires: Two buckets, a drill (or stabbing weapon), piece of wood (or bottom of another bucket), kinda a custom drill bit, water. + your TRASH!

Out of all of the physical spam you receive in the mail, leaves you rake, dead foliage, paper towel rolls, paper plates, napkins, beer boxes, egg cartons, etc., etc., etc., (any biomass material you can think of) – why not turn it into useable logs for your furnace, campfire, or cooking? Just don’t use the plastic coated things.

I’ve seen ‘devices’ you can buy that makes ‘newspaper logs’, but they never seem efficient, require you to pre-shred, take way too much time and the logs are not very solid. This is a much better method and doesn’t really cost anything.

Step 1

Get two 5 gal buckets. $3 each at walmart. Drill a lot of holes in it, about 2 inchesdown from the lips and around 3/16 size-ish. I used a soldering iron. You can use a screw driver and stab holes all in there. Go around all the bucket and on the bottom. [Todd’s note: Buckets can be had for free at bakery’s and construction sites]

Step 2

Place the holy bucket inside the other normal bucket. Start putting your papers, leaves, bio material in it. Add your water and fill’r up. Doesn’t really matter if you have too much water. You can leave these buckets of water setup by the mailbox, then just walk by and toss stuff in.

Step 3

You need a custom drill bit, which I have. A good thing to do is find an old table saw blade and weld it to s shaft of steel. This is “the hardest” part of this setup. Drill away and in seconds you will have a nice pulpy wet mess.

Step 4

Next, pull out the holy bucket and let it drain. I put the draining bucket on top of the other bucket to save the water – you can re-use the same water many times.

Step 5

You should have a press that goes far down into the bucket to press out the remaining water. I found a bucket that someone cut the bottom off.. well perfect. But you will probably want to place a bucket down on some wood, trace around the base and cut out that piece of wood to use as a press.

Step 6

Set your press inside the bucket over the pulp. Then I set the re-used water bucket inside of that bucket (because water is heavy). That will work over time. I also sat on it.. put my anvil on it.. and stood in it. It’s pretty quick. whatever heavy you have for the top.

Step 7

Now once most the water is pressed out – take it out to a sunny/dry place. Turn over the bucket and tap on the top. It will take some time to dry, depending on your location. We live in the desert so this will happen fast. If you want it to dry faster, cut these logs as you would a pizza, into sections.

Once dry, these will burn a long time.. and cost you ~ nada.

Todd’s note: Hope you enjoyed Jamie’s tutorial. He’s a fine example of people who havetraded theory for ACTION! Come check out all the other folks busy Doing the Stuff!

If you try it yourself, we’d like to know how it turns out.

Keep Doing the Stuff of self-reliance,

Todd

P.S. – You can also keep up with the Stuff we’re Doing onTwitter,Pinterest,Google +, YouTube andFacebook page… andover attheDoing the Stuff NetworkonPinterest,Google +, andFacebook.

P.P.S – If you find value in our blog, Dirt Road Girl and I would appreciate your vote onTop Prepper Sites! You can vote daily by clickinghereor on the image below. Check out all the other value-adding sites while you’re there…

Thanks for Sharing the Stuff!

Copyright:Content on this site (unless the work of a third-party) may be shared freely in digital form, in part or whole, for non-commercial use with a link back to this site crediting the author.Alllinks in articles must remain intact as originally posted in order to be republished. If you are interested a third-party article, please contact the author directly for republishing information.