Capello CR60 Tune Clock Radio with Bluetooth Speaker User Guide - Manuals Clip (2024)

Views: 75

Capello CR60 Tune Clock Radio with Bluetooth Speaker User Guide

Inside the Box

• CR60 Clock Radio with Bluetooth Speaker,
• AC power adapter
• user guide

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or ground-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Location of controls

1. SNOOZE / BRIGHTNESS
2. ALARM 1
3. POWER ON / OFF
4. SOURCE
5. ALARM 2
6. DC IN JACK
7. FM ANTENNA WIRE
8. USB CHARGING PORT
9. PLAY / RADIO PRESET
10. VOLUME +
11. TUNE UP / MIN
12. BLUETOOTH PAIR / TIME SET
13. VOLUME –
14. TUNE DOWN / HOUR
15. LED DISPLAY
16. SPEAKER
17. BATTERY COMPARTMENT

LED Display Indicators

1. BLUETOOTH
2. FM RADIO
3. ALARM 1
4. ALARM 2
5. LOW BATTERY
6. AM

Settings

Setting the clock

1. Plug in the CR60 but leave the power “OFF”.
2. Press and hold the BLUETOOTH PAIR / TIME SET button until the clock flashes in the display.
3. Press the TUNE DOWN / HOUR button repeatedly to set the hour and press the TUNE UP / MIN button repeatedly to set the minute.
4. Press the BLUETOOTH PAIR / TIME SET button again to store the new clock setting.

Setting the alarm

1. In standby mode, slide the ALARM 1 switch to the “SET” position and the display will begin flashing.
2. Press the TUNE DOWN / HOUR or TUNE UP / MIN button to set the desired alarm time.
3. Next press the VOLUME + or VOLUME – button to set the maximum alarm volume.
4. Slide the ALARM 1 switch to RADIO or BUZZ position to complete the process, the alarm time will disappear and the alarm indicator will light up on the display.

Silencing the alarm

1. When the ALARM 1 sounds, slide the ALARM 1 switch to the “OFF” position to silence the alarm.
2. To reactivate ALARM 1 the next time it is needed, slide the ALARM 1 switch to the “RADIO” or “BUZZ” position and the ALARM 1 indicator will light up on the display, then check to make sure the alarm time is correct.

Note: To silence or reactivate ALARM 2, simply follow the same directions above but use the ALARM 2 switch.

Setting the display brightness
There are three levels of display brightness available (the default setting is high).Press the SNOOZE / BRIGHTNESS button to cycle through and select the desired setting.

Playing the radio

1. With the CR60 plugged in and powered “ON”, repeatedly press the SOURCE button until FM Radio indicator lights up on the display.
2. Repeatedly press the TUNE UP / MIN or TUNE DOWN / HOUR button to manually adjust the tuning on the display until the desired station appears.
3. For auto tuning, press and hold the TUNE UP / MIN or TUNE DOWN / HOUR button until the display starts to scan, then release the button. The tuner will search and stop on the next strongest station it finds. Repeat this process until the desired station appears on the display.

Notes: Fully extend the FM antenna wire to increase reception sensitivity. Keep digital music players or mobile phones away from the FM antenna as this may cause interference. Do not place the FM antenna near the AC power adaptor as this may lead to reception interference.

Setting radio presets

1. To preset a radio station to memory, first follow the steps above to tune in the desired station.
2. Press and hold the PLAY / RADIO PRESET button to create a preset for the current station. “P” will appear and “##” (the preset number) will blink on the display.
3. Press the TUNE UP / MIN or TUNE DOWN / HOUR button to select a preset number (01- 10). Press the PLAY / RADIO PRESET button again to confirm the setting and the station will be saved into memory.
4. Repeat these steps for up to 10 presets, as desired.
5. To recall a preset station, repeatedly press the PLAY / RADIO PRESET button until the desired preset number appears in the display and the station tunes in.

Bluetooth Operation

You can stream audio wirelessly to CR60 from up to 33’ away using your iPhone, iPad, iPod, Android, laptop, or other A2DP Bluetooth enabled device.

1. Press the POWER ON/OFF button to turn on CR60.
2. Then press the SOURCE or BLUETOOTH PAIR / TIME SET button. The Bluetooth LED indicator will flash on the display.
3. Turn on your A2DP Bluetooth device and enable Bluetooth.
4. Search for Bluetooth devices and select “CR60”.
5. The Bluetooth LED indicator will change from flashing to solid indicating that your Bluetooth device is connected to CR60.

Notes:

• Press and hold the BLUETOOTH PAIR / TIME SET button for 3 seconds to disconnect the Bluetooth connection.
• The unit will return to pairing mode and the Bluetooth LED indicator on the display will flash.
• If asked for a password, enter “0000”.

Reconnecting your Bluetooth Devices
Once your Bluetooth device has been paired with CR60, it is simple to reconnect them.

1. Make sure that CR60 is powered on and within range.
2. Select “CR60” from the list on your Bluetooth device.
3. The Bluetooth LED indicator on the display will change from flashing to solid, indicating that your Bluetooth device is reconnected to CR60.

Specifications

General:

• Power Source: DC 5V 2.2A Adapter (Center Positive)
• AC Power Supply: 100-240V ~ 50/60Hz 0.8A
• Class 2 Bluetooth Ranges: 33ft (10m)
• Supported Bluetooth Profile: A2DP
• Battery Backup: 2 x 1.5V “AAA” size batteries
• Speaker: 1 x 4 ohms
• Output Power: 2W x 1
• USB Jack DC Power Output: 5V 2A

Radio section:

• Frequency Range (FM): 87.5—108 MHz

FCC STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.

Tags: Capello, Capello CR60, Capello Tune Clock Radio with Bluetooth Speaker, CR60, CR60 Tune Clock Radio with Bluetooth Speaker, Tune Clock Radio with Bluetooth Speaker, user guide